1
  2
  3
  4
  5
  6
  7
  8
  9
 10
 11
 12
 13
 14
 15
 16
 17
 18
 19
 20
 21
 22
 23
 24
 25
 26
 27
 28
 29
 30
 31
 32
 33
 34
 35
 36
 37
 38
 39
 40
 41
 42
 43
 44
 45
 46
 47
 48
 49
 50
 51
 52
 53
 54
 55
 56
 57
 58
 59
 60
 61
 62
 63
 64
 65
 66
 67
 68
 69
 70
 71
 72
 73
 74
 75
 76
 77
 78
 79
 80
 81
 82
 83
 84
 85
 86
 87
 88
 89
 90
 91
 92
 93
 94
 95
 96
 97
 98
 99
100
101
102
103
104
105
106
107
108

/*
 * Copyright (C) 2018 Kubos Corporation
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *     http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */

use radio_api::{Connection, RadioResult, Stream};
use serial;
use std::io;
use std::time::Duration;

/// Connection for communicating with actual
/// Duplex-D2 hardware
pub fn serial_connection() -> Connection {
    Connection::new(Box::new(SerialStream {}))
}

struct SerialStream {}

impl Stream for SerialStream {
    fn write(&self, data: &[u8]) -> RadioResult<()> {
        Ok(serial_send(data)?)
    }
    fn read(&self) -> RadioResult<Vec<u8>> {
        Ok(serial_receive()?)
    }
}

fn serial_send(data: &[u8]) -> io::Result<()> {
    use serial::prelude::*;
    use std::io::prelude::*;

    let mut port = try!(serial::open("/dev/ttyUSB0"));
    let settings: serial::PortSettings = serial::PortSettings {
        baud_rate: serial::Baud38400,
        char_size: serial::Bits8,
        parity: serial::ParityNone,
        stop_bits: serial::Stop1,
        flow_control: serial::FlowNone,
    };
    try!(port.configure(&settings));

    try!(port.set_timeout(Duration::from_secs(1)));

    let be_data = {
        let mut v = Vec::<u8>::new();
        for i in 0..data.len() {
            v.push(data[i].to_be());
        }
        v
    };

    try!(port.flush());
    try!(port.write(&be_data[..]));

    Ok(())
}

fn serial_receive() -> io::Result<Vec<u8>> {
    use serial::prelude::*;
    use std::io::prelude::*;

    let mut ret_msg: Vec<u8> = Vec::new();
    let mut port = try!(serial::open("/dev/ttyUSB0"));

    let settings: serial::PortSettings = serial::PortSettings {
        baud_rate: serial::Baud38400,
        char_size: serial::Bits8,
        parity: serial::ParityNone,
        stop_bits: serial::Stop1,
        flow_control: serial::FlowNone,
    };
    try!(port.configure(&settings));

    try!(port.set_timeout(Duration::from_millis(100)));

    let mut tries = 0;

    loop {
        let mut read_buffer: Vec<u8> = vec![0; 1];

        match port.read(&mut read_buffer[..]) {
            Ok(c) => {
                if c > 0 {
                    ret_msg.extend(read_buffer);
                } else {
                    tries = tries + 1;
                }
            }
            Err(_) => break,
        };
        if tries > 5 {
            break;
        }
    }

    Ok(ret_msg)
}