Working with the ISIS-OBC

Overview

This document covers the Kubos Linux features which are specific to the ISIS-OBC target, also known as the iOBC.

Please refer to Using Kubos Linux for a general guide to using Kubos Linux.

Reference Documents

iOBC Documentation

The ISIS-OBC Quickstart Guide should have been packaged with the iOBC and is a useful document for learning what each of the hardware components are, how to connect them, and what drivers need to be installed to support them.

Kubos Documentation

Status LEDs

There are four yellow LEDs present on the iOBC which give some indication of what state the board is in, along with one red LED which is lit when the system is powered:

  • Three LEDS (solid) - The system is currently running U-Boot
  • One LED (blinking) - The system is currently running Kubos Linux

Debug Console Connection

The iOBC should be shipped with an FTDI cable. This cable should be connected to the programming adapter, which should then be connected to the iOBC, to create the debug UART connection. User file transfer will take place using this connection.

Additionally, a SAM-ICE JTAG must also be connected in order to successfully connect with an iOBC.

Peripherals

The iOBC has several different ports available for interacting with peripheral devices. Currently, users should interact with these devices using the standard Linux functions. A Kubos HAL will be added in the future for the iOBC.

ADC

The iOBC has four analog input pins available:

iOBC Linux
AIN4 0
AIN5 1
AIN6 2
AIN7 3

The pins are available through the Linux device /sys/bus/iio/devices/iio\:device0/.

A single raw output value can be read from each of the pins via /sys/bus/iio/devices/iio\:device0/in_voltage{n}_raw, where {n} corresponds to the Linux AIN number.

This raw value can then be converted to microvolts by multiplying it by the value found in /sys/bus/iio/devices/iio\:device0/in_voltage_scale.

More information about the capture and use of ADC can be found in this guide from Atmel.

An ADC example is also available for reference in the Kubos repo.

GPIO

The iOBC has 27 GPIO pins available. These pins can be dynamically controlled via the Linux GPIO Sysfs Interface for Userspace as long as they have not already been assigned to another peripheral.

To interact with a pin, the user will first need to generate the pin’s device name:

$ echo {pin} > /sys/class/gpio/export

The {pin} value can be found in the below chart:

iOBC GPIO # Linux GPIO Value
0 42
1 43
2 44
3 45
4 52
5 53
6 54
7 55
8 56
9 57
10 58
11 59
12 60
13 61
14 62
15 63
16 12
17 13
18 14
19 15
20 16
21 17
22 18
23 19
24 20
25 21
26 22

For example, to interact with the iOBC’s GPIO5 pin, which has a Linux GPIO value of 53, the user will use:

$ echo 53 > /sys/class/gpio/export

Once this command has been issued, the pin will be defined to the system as ‘/sys/class/gpio/gpio{pin}’. The user can then set and check the pins direction and value.

Set GPIO5 as output:
$ echo out > /sys/class/gpio/gpio53/direction

Set GPIO23's value to 1:
$ echo 1 > /sys/class/gpio/gpio19/value

Get GPIO10's value:
$ cat /sys/class/gpio/gpio58/value

I2C

I2C Standards Doc

Kubos Linux is currently configured to support the I2C standard-mode speed of 100kHz.

The I2C bus is available as /dev/i2c-0, or through the Kubos C HAL as K_I2C1.

For examples and instructions, see the I2C HAL documentation.

PWM

The iOBC has 6 PWM pins available for use, grouped into three pairs:

  • PWM0 and PWM1
  • PWM2 and PWM3
  • PWM4 and PWM5

Users can interact with these pins through the PWM sysfs interface, and the /sys/class/pwm/pwmchip0/ directory

In order to make a pin available for use, the PWM number should be passed to the pwmchip0/export file. For example, the following would be done in order to enable access to PWM0:

$ echo 0 > /sys/class/pwm/pwmchip0/export

After doing so, a new subdirectory will be available, pwmchip0/pwm0.

From here, the pin’s properties can be configured and then it can be enabled.

Note

Due to the underlying hardware, each pair of pins must use the same period value. They may, however, have differing duty cycles.

The nanosecond value specified for period and duty cycle will be internally converted to the nearest clock divider value.

For example:

/* Set the period of the generated wave to 1 millisecond */
$ echo 1000000 > /sys/class/pwm/pwmchip0/pwm0/period

/* Set the duty cycle to 50% (.5 millisecond) */
$ echo 500000 > /sys/class/pwm/pwmchip0/pwm0/duty_cycle

/* Turn on the signal */
$ echo 1 > enable

Then, to turn the signal off:

$ echo 0 > enable

SPI

The iOBC has one SPI bus available for external use with three pre-allocated chip select pins. All pins are exposed via either an iOBC daughterboard (J5 connection) or optional iOBC header (J3 connection).

SPI Bus 1

Name Pin
MOSI SPI1_MOSI
MISO SPI1_MISO
SCLK SPI1_SPCK
CS0 SPI1_NPCS0
CS1 SPI1_NPCS1
CS2 SPI1_NPCS2

Users can interact a device on this bus using Linux’s spidev interface The device name will be /dev/spidev1.n, where n corresponds to the chip select number.

An example user program to read a value might look like this:

#include <fcntl.h>
#include <unistd.h>
#include <sys/ioctl.h>
#include <linux/types.h>
#include <linux/spi/spidev.h>

#define SPI_DEV "/dev/spidev1.0"

int fd;
uint8_t mode = SPI_MODE_0;
uint8_t bits = 8;
uint32_t speed = 1000000;
uint16_t delay = 0;
uint8_t tx[2] = {0};
uint8_t rx[2] = {0};

uint8_t value;

fd = open(SPI_DEV, O_RDWR);

/* Register to read from */
tx[0] = 0xD0;

/* Set up communication configuration */
struct spi_ioc_transfer tr = {
    .tx_buf = (unsigned long)tx,
    .rx_buf = (unsigned long)rx,
    .len = 1,
    .speed_hz = speed,
    .bits_per_word = bits,
    .cs_change = 0,
    .delay_usecs = delay,
};

/* Send request to read */
ioctl(fd, SPI_IOC_MESSAGE(1), &tr);

/* Grab result from response buffer */
value = rx[1];

close(fd);

UART

The iOBC has 2 UART ports available for use in varying capacities:

Linux Device TX Pin RX Pin RTS Pin CTS Pin
/dev/ttyS1 TX0 RX0    
/dev/ttyS3 TX2 RX2 RTS2 CTS2

Users can interact with these ports using Linux’s termios interface.

A tutorial on this interface can be found here

User Data Partition

The iOBC has a single user data partition which maps to the /home directory.

The home directories of all user accounts, except root, should live under this directory.

Warning

Any files not residing under the /home directory will be destroyed during an upgrade/downgrade