Kubos FAQs and Troubleshooting Tips¶

FAQs
Troubleshooting
- Kubos SDK
- Kubos Linux
  - I transferred a script, but it won’t run
  - Flash Troubleshooting

FAQs ¶

How do I contact y’all?¶

Our community Slack: slack.kubos.co

Our email: info@kubos.co

How do I set up the Kubos SDK?¶

See Installing the Kubos SDK

How do I check if I’m using the latest version of the Kubos Vagrant image?¶

From your host machine, issue the vagrant box outdated command.

How do I get the latest version of the Kubos Vagrant image?¶

From your host machine, issue the vagrant box update command.

Warning

This will overwrite all files in your existing image

How do I check what version of the Kubos SDK I’m running?¶

kubos version

How do I update the Kubos SDK?¶

kubos update --all

How do I check what my project’s target is?¶

kubos target

How do I see the debug output of my board?¶

STM32F407 ¶

Connect an FTDI cable to your board’s debug UART port. By default:

Yellow wire (TX) –> pin PC6.
Orange wire (RX) –> pin PC7.

Then use minicom kubos to start a serial connection session.

How do I check what version of Kubos Linux I’m running?¶

Issue the uname -r command on the target board to display the kernel information. The Kubos Linux version will be the n.n.n number after “KubOS”.

uname -r
4.4.23-KubOS-1.0.0

Troubleshooting ¶

Kubos SDK ¶

The `vagrant up` command just hangs ¶

If you’re using Windows 7 SP1, make sure you are using the correct version of Windows PowerShell.

I’ve tried other steps here, but my Kubos Vagrant image is still behaving weirdly.¶

Try logging out and restarting the VM using the vagrant reload command.

I got some weird errors while running a kubos command (`kubos build`, `kubos target`, etc)¶

Run kubos update -a to ensure that you’re using the latest version of the Kubos SDK

“error: could not install target {target} at * for {target}”¶

error: could not install target {target} at * for {target}
error: The targets registry does not provide a version of "{target}"

Run kubos link -a to re-establish the required module links for your project

“error: No module.json file.”¶

error: No module.json file.
error: The current directory does not contain a valid module.

You are not currently in a valid Kubos project directory. Alternatively, your project’s module.json file has somehow gotten deleted.

“error: failed to create link: [Errno 71] Protocol error”¶

You’re trying to create a symlink on a Windows host machine, most likely by trying to initialize a Kubos project in a shared folder.

Windows does not support symlinks, so you cannot build Kubos projects within a shared folder on a Windows machine.

I can’t build my project. I keep getting “Permission denied” errors ¶

If you copied your project from another location, it’s possible that the files are set up with root permissions only. Change the project file permissions to allow the local vagrant user to have access.

sudo chown vagrant:vagrant . -R

Kubos Linux ¶

I transferred a script, but it won’t run ¶

kubos flash preserves the file permissions of everything you transfer. Check that your file has the appropriate execute permissions turned on.

Flash Troubleshooting ¶

Flashing a file to the board can fail for various reasons. Sometimes simply reattempting the command can correct the problem.

If retrying doesn’t work, here is a list of some of the errors you might see after running the kubos flash command and the recovery actions you can take:

“No compatible FTDI device found”¶

Check that the Kubos Linux target is turned on and connected to your computer
Check that no other vagrant images are running. Only one VM can have control of the USB, so it may be that another instance currently has control of the device. You can shutdown a vagrant image with the command vagrant halt
Verify that the USB is showing up within the vagrant environment with the lsusb command. You should see an FTDI device
Verify that the USB has been mapped to a linux device. Issue the command ls /dev. You should see a /dev/ttyUSB* device. If you don’t, try rebooting your vagrant image (vagrant halt, vagrant up)

“Transfer Failed: Connection Failed”¶

The SDK was unable to connect to the Kubos Linux target

Verify that the USB has been mapped to a linux device. Issue the command ls /dev. You should see a /dev/ttyUSB* device. If you don’t, try rebooting your vagrant image (vagrant halt, vagrant up)
If this error occurs after the transfer process has started, then the SDK likely lost connection to the board. Verify that the board is still correctly connected and powered and try the flash command again.

“Transfer Failed: Invalid Password”¶

The SDK was unable to log into the Kubos Linux target. Verify that the password is correctly defined in your config.json file by issuing the kubos config command.

System appears to have hung ¶

If for some reason file transfer fails, it can take a couple minutes for the connection to time out and return control.
If you’ve waited a couple minutes and the system still appears hung, please let us know so that we can open a bug report.

My flash failed for some other reason ¶

It’s possible that the transfer timed out. Check the build/{target}/flash.log file in your project for more information about why the flash failed.

If you were trying to flash an upgrade file, simply re-enter the kubos flash command to resume the transfer.